Perlick PERL Keg Beer Faucet - Polished Chrome

Model: 630PC
53 Reviews
$39.00

90 Day Money Back Guarantee
Select Model:
IN STOCK (usually ships within 24 hours)
  • Perlick's 630PC forward sealing faucet features a low-lead polished chrome-plated brass body
  • Patented forward sealing design eliminates the need for a valve shaft exposed to beer and air
  • Spout angle is more vertical, allowing a more thorough draining after each pour and no horizontal area for beer to collect
  • Polished interior ensures a smooth flow with less agitation and less foaming
  • This faucet is easy to clean and may be cleaned in place
DESCRIPTION
FEATURES
REVIEWS
Q&A

Unique in both appearance and function, Perlick's 630PC Forward Sealing Faucet features a revolutionary ball and floating front seal design that prevents beer from being exposed to air. As a result, the handle lever does not stick and there is no build up of mold and bacteria in the faucet body. There are also fewer internal parts, which results in better reliability and fewer service calls. The 630PC features a low-lead polished chrome-plated brass construction for economical beer dispensing.

Warning WARNING: This product has Brass components. Brass alloys are known to contain trace amounts of Lead, which is known to the State of California to cause cancer and reproductive harm. For more information, go to www.P65Warnings.ca.gov.
  • All Perl faucets include a stainless steel lever for strength and sanitation.
  • Forward seat design to prevent lever from sticking
  • More sanitary than rear seating faucets
  • 1"W x 4"H x 2 3/4"D
Faucet Replacement Parts
Item630680650690Description
167829-167829-167829-167829-1Handle Jacket, Chrome
67829-1TF67829-1TFN/AN/AHandle Jacket, Tarnish Free
267820-167820-167820-167820-1Compression Bonnet, Chrome
67820-1TF67820-1TFN/AN/ACompression Bonnet, Tarnish Free
367828-167828-167828-167828-1O-Ring, Compression
467819-267819-267819-267819-2Bearing Cup
5A68726-1N/A68626-1N/AHandle Lever
5BN/A68810N/A68810Handle Lever, Push Back Creamer
667830-167830-167830-167830-1O-Ring, Pivot Ball
767933-167933-167933-167933-1O-Ring, Front Seat
8308-3-2P308-3-2P308-3-2P308-3-2PCoupling Gasket
9N/AN/A68206-168206-1Flow Control: Compensator
10N/AN/A67989SK67989SKFlow Control: Seal Kit
11N/AN/A67989LK67989LKFlow Control: Lever & Seal Kit

Follow these instructions if you need to take the faucet apart to replace worn parts.

Note: Anytime the Front Seat (I), O-ring (H) or Coupling Gasket(s) are removed, they should be replaced. Always use OEM replacement parts.

TO DISASSEMBLE:

  1. If faucet is USED, soak faucet in warm cleaning solution for 1-2 minutes to free up bonnet and handle jacket. If the faucet is NEW, submerge the faucet in warm water for 5 seconds.
  2. Unscrew and remove Jacket (1).
  3. Unscrew and remove Compression Bonnet (2).
  4. Remove Coupling Gasket (8) only if cut or worn.
  5. To remove the Handle Lever Assembly (5A or 5B), lift it upward and push back.
  6. To remove Front Seat (7) use a small screwdriver from the bonnet end of the faucet.
  7. To remove O-ring (6) use a small screwdriver from the bonnet end of the faucet.
  8. Inspect O-rings for wear or damage and replace as necessary.
  9. To remove flow control lever, unscrew cap and pull out.
  10. Remove flow control compensator from rear of faucet.

TO ASSEMBLE:

  1. Re-install O-ring (6) into O-ring groove from bonnet end (use a small blunt screwdriver).
  2. Re-install front Seat (7) into O-ring groove (use a small blunt screwdriver). Note: Seat must move freely in seat groove.
  3. Re-install Handle Lever Assembly (5A or 5B).
  4. Re-install Bearing Cup (4).
  5. Re-install Bonnet Washer (3) into Compression Bonnet (2).
  6. Re-install Compression Bonnet (2). Tighten by hand only. Do not use any tool, as this can damage the faucet.
  7. Re-install Handle Jacket (1).
  8. Re-install Coupling Gasket (8) if removed.
  9. Install flow control compensator into rear of faucet and orientate so level engagement hole is facing lever insertion hole.
  10. Install flow control lever, ensure pin on end of lever is aligned with compensator engagement hole and tighten cap.
UPC: 847808038046

12/28/2023

Perlick 630SS Forward Sealing Faucet
Shiner Bock

Worth the money! You will never be happy with a standard faucet again that sticks. This Perlick faucet is so smooth!!

09/07/2023

Better faucet
Lewsh

Was using old style faucets with internal piston. This faucet has no piston, is very smooth and light in the hand to operate. So far no sticking of faucets.

05/04/2022

Riley’s Irish Pub
Mike

We serve a lot of darker larger and ale style beers. We have always struggled with the faucet gunking up just after a couple days of non use causing the faucet to stick. This style of faucet has solved that problem

12/04/2021

Commercial Grade Double Gauge Secondary
Tom

easy to install ad is a great upgrade

04/18/2020

Top quality
Tony

This product is so much bette4 then the standard tap that comes with the keg.

Showing Reviews 1-5 of 53
 1 2 3   Last
Question:
Where are these manufactured?
by hoobie on October 06, 2019
Answer:
Perlick products are manufactured in Milwaukee, Wisconsin
by Ben on October 10, 2019
Staff Answer

CONNECT WITH US!

@BeverageFactory
Added to Cart

.....