Taprite T742HP - Primary Double Gauge CO2 Gas Beer Regulator with Polyethylene Knob

Regular Price: $64.94
You Save 20%
$51.95

You can use this low pressure regulator on any CO2 tank with a CGA-320 valve. CO2 tanks have a male thread (CGA-320); these regulators have a female thread. This regulator features dual gauges to measure psi as well as the volume of CO2 in the cylinder, indicating how much CO2 is left in the cylinder and when you should have it refilled. The knob on the front is used to adjust the output pressure.

This low pressure regulator allows for an adjusted pressure from 1 to 50 psi with a safety blow off at 60 psi. This regulator can be used as a primary regulator for mixed gas or CO2.

  • Red polycarbonate bonnet will not chip, break or fade.
  • Non-adjustable "shut-down" built in to the body of regulator
  • The high pressure ports have left-hand female threads to prevent their use as a lo-pressure outlet
  • The non-removable adjusting screw is designed so that when it is turned all the way in the maximum downstream delivery pressure will not exceed 50 PSIG.
  • Internal relief valve opens whenever delivery pressure exceeds set pressure by 15 PSIG. This feature serves as a warning that the seat or diaphragm may be worn or damaged and should be replaced.
  • Sintered metal flow control filter in the inlet nipple to prevent dirt and other particles from damaging internal regulator parts.
  • Permanent Quad-Ring Seal on inlet nipple helps eliminate a source of leaks... no need to use a new fiber washer each time tank is changed.
  • Outlet features NADS 1600C shutoff which eliminates a source of gas leaks. The duck bill check valve helps prevent product back-up into the regulator, a common cause of malfunction in the regulating and relief valve parts. Hose barb end designed for use with 5/16" I.D. pressure tubing.
  • All regulators are pressure tested to assure in-field reliability.
  • Seat assembly is easily replaceable in-field... no need to remove regulator from tank.
  • Polycarbonate bonnet will not chip, break or fade.
  • The non-adjustable "shut-down" safety is built into the body of the regulator where it cannot be removed or easily circumvented. In event of a failure of the regulator seat this safety will respond instantly, isolating the product container from potentially dangerous high pressure. The product container pressure level will not exceed the factory set blow-off of 55 - 65 PSIG.
  • The high pressure ports have left-hand female threads to prevent their use as a lo-pressure outlet... (If replacement parts are required, contact factory).
  • The non-removable adjusting screw is designed so that when it is turned all the way in the maximum downstream delivery pressure will not exceed 60 PSIG.
  • Internal relief valve opens whenever delivery pressure exceeds set pressure by 15 PSIG. This feature serves as a warning that the seat or diaphragm may be worn or damaged and should be replaced.
  • Sintered metal flow control filter in the inlet nipple to prevent dirt and other particles from damaging internal regulator parts.
  • Permanent Quad-Ring Seal on inlet nipple helps eliminate a source of leaks... no need to use a new fiber washer each time tank is changed.
  • Outlet features NADS 1600C shutoff which eliminates a source of gas leaks. The ball-type check valve helps prevent product back-up into the regulator, a common cause of malfunction in the regulating and relief valve parts. Hose barb end designed for use with 5/16" I.D. pressure tubing.
  • All regulators are pressure tested to assure in-field reliability.
  • Seat assembly is easily replaceable in-field... no need to remove regulator from tank.
  • Each regulator comes with instructions for proper installation and use procedures

UPC: 608866314523

Taprite T742HP - Primary Double Gauge CO2 Gas Beer Regulator with Polyethylene Knob Reviews

Average Customer Rating:
(5)
(based on 9 reviews) 
Good Buy
by:Pete (03-03-2015)
Anchorage
Comments:If your looking for an economical regulator that's built to last this is for you. The easy to read dial and nice adjustment knob makes this a great regulator. Hook inning it up is a breeze which requires little effort and most importantly is leak free. This is essential for legging your beer.
Bottom Line:I would recommend this product.
 
Just whatnI needed
by:Garmat55 (02-21-2015)
Orland Park,IL
Comments:The one that came with my the stock set never worked correctly. This was the answer. Easy to install and works great.
Bottom Line:I would recommend this product.
 
Works well!
by:Joe (10-03-2014)
Del. Co. PA
Comments:I like adjustable knob to control air pressure.
Bottom Line:I would recommend this product.
 
Simplicity and Competitive Price
by:Ron (07-15-2014)
Athens, Ga
Comments:This is an excellent piece of equipment, and it appears to do what I want effortlessly. I needed a set to help me when cleaning out kegs and lines, and it is a simple and relatively inexpensive way to accomplish this. In addition, it allows me the ability to a apply CO2 to a single meg.
Bottom Line:I would recommend this product.
 
This product is great
by:Terry (03-17-2014)
Sugar land Tx
Comments:Very easy to setup and to adjust. I would buy it again.
Bottom Line:I would recommend this product.
 
Shipping Calculator
Enter Your Shipping Zip Code:
Shipping Options
Please enter a zip code.
All charges are based on a quantity of 1.
Click "Add to Cart" above to change quantities
and make actual ship method selection.