D System Ergonomic Keg Coupler with Lever Handle and Stainless Steel Probe Reviews

Click here to return to the D System Ergonomic Keg Coupler with Lever Handle and Stainless Steel Probe

Product Reviews

Product Reviews

D System Ergonomic Keg Coupler with Lever Handle and Stainless Steel Probe Reviews

Average Customer Rating:
(5)
(based on 14 reviews) 
Excellent
by:Tom (11-02-2016)
Colorado
Comments:Easy to use for an old fart.
Bottom Line:I would recommend this product.
 
Kegco D System Coupler
by:Ryan (05-05-2016)
West Linn, OR
Comments:Works perfectly and was less expensive than most.
Bottom Line:I would recommend this product.
 
The Big D!
by:Micklex (04-12-2016)
Federal Way, WA.
Comments:I've used this with my keezer- as the first beer I've dispensed from my taps. It works great, was easy to put on the keg, and with the right adapters for my hose lines everything connected perfectly. Do keep in mind that it comes as shown- meaning if you have 3/8 ID line you'll need different connectors to adapt to your equipment and it doesn't have the adapter at all for the beer out line. Standard shank adapters fit.
Bottom Line:I would recommend this product.
 
Fixed my leaking problem
by:Bill (03-16-2016)
Gainesville, GA
Comments:Fixed my leaking problem where just replacing 0-rings on the older coupler wasnt getting it done.
Bottom Line:I would recommend this product.
 
Great stainless coupler
by:Jaeger (03-15-2016)
Central Texas
Comments:Probe is machined stainless, the body looks like cast 316. The handle tilts to ease in catch release. I'm impressed, will be buying more.
Bottom Line:I would recommend this product.
 
Nice design
by:Kevin (01-20-2015)
Pullman, WA
Comments:I was sold on these based on comments from users and would like to add here as well. I bought 4 of them to replace my old units, while installing 2 new cooler boxes. My old cooler required using a 1/6 barrel, and that necessity was eliminated on the new set-up. I read that these taps would not work with the small diameter kegs but that didn't really concern me as I didn't foresee a need for the little kegs in the future. I forgot about a final 1/6th I had in stock prior to installing the new taps, and it wasn't until I snapped the lever down, tapping this keg that I remembered it shouldn't fit..? Well it does, just fine... better than my old tap that "worked". I later noticed on the boxes they come in it notes "Small handle". I'm not sure if there are options here (didn't recall seeing one) or if this is an upgraded / new design to cure an old symptom, but these from the Beverage Factory do work on sixth barrels... maybe someone else can confirm?
Bottom Line:I would recommend this product.
 
WELL MADE
by:SPEED3CHRIS (11-16-2014)
ARROYO GRANDE, CA
Comments:THIS COUPLER IS WELL MADE AND MUCH EASIER TO USE THAN WHAT CAME WITH MY COOLER. I REALLY LIKE THE LEVER. I WOULD RECOMMED THIS PRODUCT.
Bottom Line:I would recommend this product.
 
super easy to use
by:mark (07-03-2014)
Massachusetts
Comments:you can use it with one hand. Screw it in click the handle down and done
Bottom Line:I would recommend this product.
 
not for 1/6 kegs
by:Brian (07-01-2014)
St. Louis
Comments:The handle is too long and angled down. Will not latch on 1/6 barrels.
Bottom Line:I would not recommend this product.
 
Very nice tapper
by:Steve (05-17-2014)
San Jose, CA
Comments:Well built, fastens firm, very good tapper.
Bottom Line:I would recommend this product.
 
Great tap! Doesn't fit 1/6th Barrel Kegs
by:Usefuljon (12-27-2013)
Seattle, WA
Comments:Great design, wonderful handle, solid construction, doesn't fit on 1/6th barrel kegs. The handle hits the edge of the keg preventing it from locking into place.
Bottom Line:I would recommend this product.
 
Great product
by:Parkertown or bust (12-16-2013)
Little egg harbor nj
Comments:I bought 3 new taps and they were great. I belong to a hunting club we tapped 11 kegs in a week and not one splash of
Beer when tapping . Highly
Recommend
Bottom Line:I would recommend this product.
 
Slim Quarter Kegs
by:Usefuljon (12-13-2013)
Seattle, WA
Comments:The handle bumps against the rim of the smaller kegs making it impossible to tap. Amazing build quality and the ratchet handle is a dream. It just doesn't fit the kegs I have in my system. A note about the longer handle would be good to add to the description.
Bottom Line:I would recommend this product.
 
Great product
by:JD (11-21-2013)
Rock Hill, SC
Comments:I bought this as a replacement for an older coupler that had a faulty pressure relief valve. The ratchet style release is so much easier than the old pull style.
Bottom Line:I would recommend this product.