Taprite

2-Product Dual Pressure Kegerator Co2 Regulator

Model:T752HP
Regular Price: $142.49
You Save $28.50
$113.99

This Taprite T752HP 2-Product Dual Pressure Kegerator Co2 Regulator allows you to tap two kegs at the same time and individually control the pressure to each keg!

The regulator has two separate gauges to individually measure the pressure to each keg and allow you to adjust it particularly for the type of beer or beverage you are drinking. A third gauge (left gauge) shows you how much CO2 is left in the tank, so you don't run out. Individual air shut off valves allow for each CO2 line to be turned on/off independently. Preset safety pressure relief valve automatically releases at 55-65 PSI.

The lightweight polycarbonate bonnet is durable and will not corrode in wet environments. No special tools are required to raise or lower the CO2 pressure. The easy to use cap knob simply pulls out to adjust pressure up or down then pushes back in to lock in pressure.

Dimensions: 9"W x 7 1/2"H x 5 1/2"D

Warning WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and reproductive harm. For more information, go to www.P65Warnings.ca.gov.
  • Dual Primary Regulators allow you to tap two kegs at the same time and control the pressure to each
  • 0-60 gauges measure pressure to each keg
  • 0-2000 gauge measures CO2 in tank
  • Individual shut off valves allow you to switch on/off each CO2 line
  • High CO2 volumetric flow to insure continuity in product dispensing
  • Polycarbonate Bonnet will not chip, break or fade
  • 10 Micron filter built in to keep contaminants out of regulator
UPC: 608938598721

2-Product Dual Pressure Kegerator Co2 Regulator Reviews

Average Customer Rating:
(5)
(based on 13 reviews) 
Excellent Product
by:Dano (07-11-2017)
The Woodlands, TX
Comments:I am very happy with this product, though I would have liked a pressure release valve on each line.
Bottom Line:I would recommend this product.
 
Very nice
by:Bill (09-29-2016)
MN
Comments:Very nice gauge for the price. I especially like the dials which are easy to make fine adjustments
Bottom Line:I would recommend this product.
 
Very nice
by:Bill (09-29-2016)
MN
Comments:Very nice gauge for the price. I especially like the dials which are easy to make fine adjustments
Bottom Line:I would recommend this product.
 
Great!
by:Gordon (01-20-2015)
Philadelphia, PA
Comments:For the first time I've been able to pour foam-free beers! Amazing the difference a new regulator makes. Other people complained about the knobs being hard to pull out or turn. I don't find that to be an issue. Great product!
Bottom Line:I would recommend this product.
 
Easy operation and set-up
by:Seymour Brewski (05-12-2014)
Phoenix, AZ
Comments:I bought this to split one C02 tank between two taps. Easy setup and install and works great!
Bottom Line:I would recommend this product.
 
Loading.....
Question:
Yes or no do keep regulator in the refrigerator or outside. What is your recommendation.thanks
by Chance on October 26, 2018
Answer:
Hello Chance,

You can keep your regulator on the inside of the fridge or the outside, neither placement will effect how the regulator will operate. I would base this on how much room you have in the fridge, if it is a tight space maybe consider placing the C02 tank with the regulator on the outside if possible. Hope this helps and thank you for the question.

Thank you,
by Hector on October 29, 2018
Staff Answer
Question:
Tap rite 2 product dual pressure regulator. What is the barb size on the outlets of this regulator?
by Brewmaster on January 28, 2019
Answer:
Barbs are 5/16th and 3/8ths for all draft gas systems
by Dave on March 25, 2019
Staff Answer