Perlick PERL Keg Beer Faucet - Stainless Steel

Model: 630SS

53 Reviews

$64.99

IN STOCK (usually ships within 24 hours)

This NSF-approved Perlick 630SS Forward Sealing Faucet features a 304 stainless steel construction that will not pit, tarnish, or taint the flavor of beer or wine
Patented forward sealing design eliminates the need for a valve shaft exposed to beer and air
Spout angle is more vertical, allowing a more thorough draining after each pour and no horizontal area for beer to collect
Polished interior ensures a smooth flow with less agitation and less foaming
This faucet is easy to clean and may be cleaned in place

DESCRIPTION

FEATURES

REVIEWS

Q&A

Thanks to its 304 stainless steel construction, this NSF-approved Perlick 630SS Forward Sealing Faucet will not pit, tarnish, or taint the flavor of beer, wine, and other beverages. It features a revolutionary ball and floating front seal design that prevents beer from being exposed to air, so the handle lever won't stick and there will be no build up of mold and bacteria in the faucet body. It also has fewer internal parts, resulting in better reliability and fewer service calls.

All Perl faucets include a stainless steel lever for strength and sanitation.
Forward seat design to prevent lever from sticking
More sanitary than rear seating faucets
1"W x 4"H x 2 3/4"D

Faucet Replacement Parts
Item	630	680	650	690	Description
1	67829-1	67829-1	67829-1	67829-1	Handle Jacket, Chrome
1	67829-1TF	67829-1TF	N/A	N/A	Handle Jacket, Tarnish Free
2	67820-1	67820-1	67820-1	67820-1	Compression Bonnet, Chrome
2	67820-1TF	67820-1TF	N/A	N/A	Compression Bonnet, Tarnish Free
3	67828-1	67828-1	67828-1	67828-1	O-Ring, Compression
4	67819-2	67819-2	67819-2	67819-2	Bearing Cup
5A	68726-1	N/A	68626-1	N/A	Handle Lever
5B	N/A	68810	N/A	68810	Handle Lever, Push Back Creamer
6	67830-1	67830-1	67830-1	67830-1	O-Ring, Pivot Ball
7	67933-1	67933-1	67933-1	67933-1	O-Ring, Front Seat
8	308-3-2P	308-3-2P	308-3-2P	308-3-2P	Coupling Gasket
9	N/A	N/A	68206-1	68206-1	Flow Control: Compensator
10	N/A	N/A	67989SK	67989SK	Flow Control: Seal Kit
11	N/A	N/A	67989LK	67989LK	Flow Control: Lever & Seal Kit

Follow these instructions if you need to take the faucet apart to replace worn parts.

Note: Anytime the Front Seat (I), O-ring (H) or Coupling Gasket(s) are removed, they should be replaced. Always use OEM replacement parts.

TO DISASSEMBLE:

If faucet is USED, soak faucet in warm cleaning solution for 1-2 minutes to free up bonnet and handle jacket. If the faucet is NEW, submerge the faucet in warm water for 5 seconds.
Unscrew and remove Jacket (1).
Unscrew and remove Compression Bonnet (2).
Remove Coupling Gasket (8) only if cut or worn.
To remove the Handle Lever Assembly (5A or 5B), lift it upward and push back.
To remove Front Seat (7) use a small screwdriver from the bonnet end of the faucet.
To remove O-ring (6) use a small screwdriver from the bonnet end of the faucet.
Inspect O-rings for wear or damage and replace as necessary.
To remove flow control lever, unscrew cap and pull out.
Remove flow control compensator from rear of faucet.

TO ASSEMBLE:

Re-install O-ring (6) into O-ring groove from bonnet end (use a small blunt screwdriver).
Re-install front Seat (7) into O-ring groove (use a small blunt screwdriver). Note: Seat must move freely in seat groove.
Re-install Handle Lever Assembly (5A or 5B).
Re-install Bearing Cup (4).
Re-install Bonnet Washer (3) into Compression Bonnet (2).
Re-install Compression Bonnet (2). Tighten by hand only. Do not use any tool, as this can damage the faucet.
Re-install Handle Jacket (1).
Re-install Coupling Gasket (8) if removed.
Install flow control compensator into rear of faucet and orientate so level engagement hole is facing lever insertion hole.
Install flow control lever, ensure pin on end of lever is aligned with compensator engagement hole and tighten cap.

UPC: 847808028368

11/06/2013

Fantastic faucet

Gary

This is a really nice faucet. I bought it for personal use in my home kegerator. It is attractive, it works well, and it certainly meets my expectations. What I like most is the easy, remarkably smooth action with little to no post pour drips.

10/27/2013

Beautiful, well crafted, won't corrode

Rob

I've seen friends with kegerators who skimped on faucets which a few years down the road had chrome corroding/chipping (think what nice wheels look like after a bad winter). That won't happen with these, and they look damn good.

10/14/2013

Best faucet ever

Mike

Bought this after regularly pouring perfect beers from my friends system that has it, and always fighting with a stuck/sticky tap on my system. You can feel the quality and smoothness on the draw, all parts are nice and tight with no play, I love this faucet!

09/24/2013

Not sticky, very shiny.

Brad

I purchased these as an upgrade based off a friends recommendation. I only pour beer 2-3 times a week and so far these do not stick at all.
The only thing I would change is for Perlick to include rubber caps for when not in use. But you can get those separately for cheap.

09/12/2013

Great upgrade

Tommy

Replaced a standard faucet with the Perlick Stainless. The design is simple, the beer pours better and it should last many years. Will be giving a Perlick Faucet as a Holiday gift to two other friends with kegerators. Cheers!

Showing Reviews 41-45 of 53

Question:

Where are these manufactured?

by hoobie on October 06, 2019

Answer:

Perlick products are manufactured in Milwaukee, Wisconsin

by Ben on October 10, 2019

Staff Answer

CONNECT WITH US!

@BeverageFactory

Perlick PERL Keg Beer Faucet - Stainless Steel

TO DISASSEMBLE:

TO ASSEMBLE:

CONNECT WITH US!

Added to Cart