Taprite Primary Double Gauge CO2 Gas Beer Regulator with Polyethylene Knob

Model: T742HP
14 Reviews
$126.65SAVE 25% - $31.66
$94.99

90 Day Money Back Guarantee
IN STOCK (usually ships within 24 hours)
  • Low pressure gauge (the top gauge) indicates output pressure to keg
  • High pressure gauge (the side gauge) indicates CO2 Tank pressure remaining
  • Duck bill check valve helps prevent product back-up into the regulator, a common cause of malfunction
  • Red polycarbonate plastic bonnet provides easy pressure adjustment and will not chip, break, or fade
  • All regulators are pressure tested to assure in-field reliability
DESCRIPTION
FEATURES
REVIEWS
Q&A

You can use this low pressure regulator on any CO2 tank with a CGA-320 valve. CO2 tanks have a male thread (CGA-320); these regulators have a female thread. This regulator features dual gauges to measure psi as well as the volume of CO2 in the cylinder, indicating how much CO2 is left in the cylinder and when you should have it refilled. The knob on the front is used to adjust the output pressure.

This low pressure regulator allows for an adjusted pressure from 1 to 50 psi with a safety blow off at 60 psi. This regulator can be used as a primary regulator for mixed gas or CO2.

  • Red polycarbonate bonnet will not chip, break or fade.
  • Non-adjustable "shut-down" built in to the body of regulator
  • The high pressure ports have left-hand female threads to prevent their use as a lo-pressure outlet
  • The non-removable adjusting screw is designed so that when it is turned all the way in the maximum downstream delivery pressure will not exceed 50 PSIG.
  • Internal relief valve opens whenever delivery pressure exceeds set pressure by 15 PSIG. This feature serves as a warning that the seat or diaphragm may be worn or damaged and should be replaced.
  • Sintered metal flow control filter in the inlet nipple to prevent dirt and other particles from damaging internal regulator parts.
  • Permanent Quad-Ring Seal on inlet nipple helps eliminate a source of leaks... no need to use a new fiber washer each time tank is changed.
  • Outlet features NADS 1600C shutoff which eliminates a source of gas leaks. The duck bill check valve helps prevent product back-up into the regulator, a common cause of malfunction in the regulating and relief valve parts. Hose barb end designed for use with 5/16" I.D. pressure tubing.
  • All regulators are pressure tested to assure in-field reliability.
  • Seat assembly is easily replaceable in-field... no need to remove regulator from tank.
Warning WARNING: This product has Brass components. Brass alloys are known to contain trace amounts of Lead, which is known to the State of California to cause cancer and reproductive harm. For more information, go to www.P65Warnings.ca.gov.
  • Polycarbonate bonnet will not chip, break or fade.
  • The non-adjustable "shut-down" safety is built into the body of the regulator where it cannot be removed or easily circumvented. In event of a failure of the regulator seat this safety will respond instantly, isolating the product container from potentially dangerous high pressure. The product container pressure level will not exceed the factory set blow-off of 55 - 65 PSIG.
  • The high pressure ports have left-hand female threads to prevent their use as a lo-pressure outlet... (If replacement parts are required, contact factory).
  • The non-removable adjusting screw is designed so that when it is turned all the way in the maximum downstream delivery pressure will not exceed 60 PSIG.
  • Internal relief valve opens whenever delivery pressure exceeds set pressure by 15 PSIG. This feature serves as a warning that the seat or diaphragm may be worn or damaged and should be replaced.
  • Sintered metal flow control filter in the inlet nipple to prevent dirt and other particles from damaging internal regulator parts.
  • Permanent Quad-Ring Seal on inlet nipple helps eliminate a source of leaks... no need to use a new fiber washer each time tank is changed.
  • Outlet features NADS 1600C shutoff which eliminates a source of gas leaks. The ball-type check valve helps prevent product back-up into the regulator, a common cause of malfunction in the regulating and relief valve parts. Hose barb end designed for use with 5/16" I.D. pressure tubing.
  • All regulators are pressure tested to assure in-field reliability.
  • Seat assembly is easily replaceable in-field... no need to remove regulator from tank.
  • Each regulator comes with instructions for proper installation and use procedures
UPC: 608866314523

01/29/2014

Great Economy Regulator
Chris

Dual regulator has performed as expected. Easy to adjust

12/24/2013

Solid feel, good quality
Richard

Currently using the regulator to carbonate water. It has a solid feel, and is easy to adjust. It's shipped securely in its own box and should arrive to you in perfect shape. Overall, it's an excellent product and is doing exactly as it was described.

08/04/2013

Taprite T742HP
F

This is a replacement to an older (dented) regulator I own. The best part I found about this regulator is the pressure knob. It's very easy to dial in and the duel pressure gauges are a must.

06/17/2013

Good regulator
Dennis

The hand turn knob makes it easy to set the perfect pressure of my beer tap

Showing Reviews 11-14 of 14
First   1 2 3

Be the first to ask a question.

CONNECT WITH US!

@BeverageFactory
Added to Cart

.....