Perlick PERL Keg Beer Creamer Faucet - Stainless Steel
Model: 680SS- This Perlick 680SS Forward Sealing Faucet features a fingertip push back control that adds just the right amount of head
- Patented forward sealing design eliminates the need for a valve shaft exposed to beer and air
- This NSF-approved faucet has a stainless steel construction that will not pit or tarnish
- Spout angle is more vertical, allowing a more thorough draining after each pour and no horizontal area for beer to collect
- Polished interior ensures a smooth flow with less agitation and less foaming
This Perlick 680SS Push-Back Creamer Faucet enables the operator to pour the precise amount of foam every time. Pushing the handle back moves a stainless steel piston, which exposes small holes. The turbulence created by beer passing through the holes produces a creamy head.
Thanks to its stainless steel construction, this NSF-approved faucet will not pit or tarnish. It features a revolutionary ball and floating front seal design that prevents beer from being exposed to air, so the handle lever won't stick and there will be no build up of mold and bacteria in the faucet body. The spout angle is more vertical on this faucet to allow for a more thorough draining after each pour, so there is no horizontal area for beer to collect. It also has fewer internal parts, resulting in better reliability and fewer service calls.
- All Perl faucets include a stainless steel lever for strength and sanitation.
- Forward seat design to prevent lever from sticking
- More sanitary than rear seating faucets
- 1"W x 4"H x 2 3/4"D
Faucet Replacement Parts | |||||
---|---|---|---|---|---|
Item | 630 | 680 | 650 | 690 | Description |
1 | 67829-1 | 67829-1 | 67829-1 | 67829-1 | Handle Jacket, Chrome |
67829-1TF | 67829-1TF | N/A | N/A | Handle Jacket, Tarnish Free | |
2 | 67820-1 | 67820-1 | 67820-1 | 67820-1 | Compression Bonnet, Chrome |
67820-1TF | 67820-1TF | N/A | N/A | Compression Bonnet, Tarnish Free | |
3 | 67828-1 | 67828-1 | 67828-1 | 67828-1 | O-Ring, Compression |
4 | 67819-2 | 67819-2 | 67819-2 | 67819-2 | Bearing Cup |
5A | 68726-1 | N/A | 68626-1 | N/A | Handle Lever |
5B | N/A | 68810 | N/A | 68810 | Handle Lever, Push Back Creamer |
6 | 67830-1 | 67830-1 | 67830-1 | 67830-1 | O-Ring, Pivot Ball |
7 | 67933-1 | 67933-1 | 67933-1 | 67933-1 | O-Ring, Front Seat |
8 | 308-3-2P | 308-3-2P | 308-3-2P | 308-3-2P | Coupling Gasket |
9 | N/A | N/A | 68206-1 | 68206-1 | Flow Control: Compensator |
10 | N/A | N/A | 67989SK | 67989SK | Flow Control: Seal Kit |
11 | N/A | N/A | 67989LK | 67989LK | Flow Control: Lever & Seal Kit |
Follow these instructions if you need to take the faucet apart to replace worn parts.
Note: Anytime the Front Seat (I), O-ring (H) or Coupling Gasket(s) are removed, they should be replaced. Always use OEM replacement parts.
TO DISASSEMBLE:
- If faucet is USED, soak faucet in warm cleaning solution for 1-2 minutes to free up bonnet and handle jacket. If the faucet is NEW, submerge the faucet in warm water for 5 seconds.
- Unscrew and remove Jacket (1).
- Unscrew and remove Compression Bonnet (2).
- Remove Coupling Gasket (8) only if cut or worn.
- To remove the Handle Lever Assembly (5A or 5B), lift it upward and push back.
- To remove Front Seat (7) use a small screwdriver from the bonnet end of the faucet.
- To remove O-ring (6) use a small screwdriver from the bonnet end of the faucet.
- Inspect O-rings for wear or damage and replace as necessary.
- To remove flow control lever, unscrew cap and pull out.
- Remove flow control compensator from rear of faucet.
TO ASSEMBLE:
- Re-install O-ring (6) into O-ring groove from bonnet end (use a small blunt screwdriver).
- Re-install front Seat (7) into O-ring groove (use a small blunt screwdriver). Note: Seat must move freely in seat groove.
- Re-install Handle Lever Assembly (5A or 5B).
- Re-install Bearing Cup (4).
- Re-install Bonnet Washer (3) into Compression Bonnet (2).
- Re-install Compression Bonnet (2). Tighten by hand only. Do not use any tool, as this can damage the faucet.
- Re-install Handle Jacket (1).
- Re-install Coupling Gasket (8) if removed.
- Install flow control compensator into rear of faucet and orientate so level engagement hole is facing lever insertion hole.
- Install flow control lever, ensure pin on end of lever is aligned with compensator engagement hole and tighten cap.
01/27/2017
Great item to have! Harley GaryWorks like a charm! No extra dripping!
10/20/2016
Excellent JohnSimply the best. Great design, Does not stick, Stainless, Tried and true.
09/07/2016
Nice product. RickI use this on my personal meiser. I like the way it looks and works.
03/23/2016
Love these faucets! MichaelVery clean, smooth operation, open wide open for the best pours, and these never stick! We use these for all of our draft accounts in the Philippines and they're wonderful and reliable.
Be the first to ask a question.
02/23/2017
Best faucet availableBest faucet I've ever used, highly recommended to replace those sticky faucets