Kegco Grain Mill with 11lb Hopper and 3 Rollers

Model: KM11GM-3R
23 Reviews
$334.00SAVE 35% - $116.90


90 Day Money Back Guarantee
IN STOCK (usually ships within 24 hours)
  • 11 lb. capacity aluminum grain hopper
  • Heavy-duty three-roller mill with adjustable secondary gap-spacing
  • Features integral drive shaft and axles
  • Grain mill can be hand-cranked or motorized with a corded electric drill
  • Now includes a black metal base that fits over common 5 gallon buckets

The Kegco KM11GM-3R Grain Mill is perfect for large batches and high efficiency milling. With three rollers, all your grain will be crushed twice in one cycle. The initial crush is through the fixed gap between the top two rollers, and then the grain passes through the second gap between the drive roller and the adjustable bottom third roller. The initial pass slightly flattens the grain, getting it ready for the next crush that breaks apart the grains and loosens the starch with minimal husk damage

The aluminum hopper can hold up to 11 lbs of grains and the roller body features an alloy block frame that houses three steel rollers on stainless steel ball bearings. The drive shaft and all axles are integral to the roller, which makes clockwise or counter-clockwise drive possible. A hand crank is included, but the mill can be easily motorized with a corded electric drill. You don't need any additional attachments, just stick the drill on and go. Stainless knurled knobs allow a gap spacing adjustment range of .070". Adjusting is simple - just loosen the adjustment screws, adjust the gap and tighten the adjustment screws. Now includes a black metal base that fits over common 5 gallon buckets.

  • 6" long adjustable gap
  • Fully adjustable mill
  • 0.060 fixed primary gap, 0-0.065 fully-adjustable secondary gap
  • Dual eccentric adjusters built from stainless steel for no galling
  • 8 lbs / minute is average throughput
  • 6" x 1.5" diameter steel rollers
  • Crankshaft can be turned clockwise or counterclockwise
  • Durable alloy frame
  • Stainless steel ball bearings
UPC: 700697198881


3 roller mill
Bobby Redtop

To mill mill grain for mash
Price wa good price for 3 roller
No instructions, precise mill markings are not. But mills the grain easily, when you figure it out the slower RPM with drill the better crush & look only at grain crush make numbers even on both sides but numbers do not represent the crush size or actual gap between 2nd and 3rd rollers, size of the crushed grain is the goal...


Great price

This is my first mill, it was a great price as I paid about the same for a 3 roller as many models charge for a 2 roller. I have only used it a couple times but it chews through grain like a champ and gives a very consistent crush, I recommend using a low speed power drill instead of the hand crank to save your arm. My only real complain is that adjusting it is somewhat difficult to figure out until you get used to it. Once i figured out to use a feeler gauge instead of the markings on the adjusters, it was fine.


Great unit

I put 12 lbs of grain thru this in 1.5 minutes and I was going slow. The grind was perfect and I hit my brewing numbers. My wife said "brewing won't be as fun anymore, as I am not cussing my old grinder".



Good Oat Crimper

Bought this to process raw oats for horse feed. So far so good. We attached a 10a high torque drill and it makes short work of several pounds of oats.

Just one negative: The adjustment of the third roller can “cam” either way, and is indexed the same each way. However, there was no explanation provided as to this two-way adjustment feature. Experimenting with it gives widely varied results, and we would have benefited from a short paragraph on this feature.

Got it dialed in easily though with a little trial and error.


Quality Mill at a Great Price

Great mill that is easy to adjust and appears to be very durable. Extremely happy with this mill and would surely buy it again.

Showing Reviews 11-15 of 23
First   1 2 3 4 5  
what size and weight does the box have. I need the information to send to Colombia
by Wilher on October 23, 2018
Shipping weight is 20 lbs and packaging dimensions are 14" x 12" x 12".
by Krystina on October 24, 2018
Staff Answer
What is the optimum rpm for powering a kegco 3 roller mill?
by waterpirate on November 03, 2018
Hello, This unit has been designed to run at slow and fast speeds resulting in the consistent grain crushing results.
by Ben on November 08, 2018
Staff Answer
Where is this made?
by Tony on December 05, 2018
Hello Tony,

This is made over seas to be more specific China. hope this helps and thank you for your question.

Thank you,
by Hector on December 06, 2018
Staff Answer
How is 25% off of $159.49 result in $10? You all need to check your math.
by Leo Wiszniewski on May 16, 2019
The item already has 20% off. The 25% off adds the additional 5%.
by Jake on July 31, 2019
Staff Answer
Can the mill be adjusted for a fine crush used in BIAB method?
by TC on August 19, 2019
Yes, this grain mill will crush a very fine consistency. from 0.00 to 0.065

0.060 fixed primary gap, 0-0.065 fully-adjustable secondary gap
by Ben on August 23, 2019
Staff Answer
Showing Questions 1-5 of 15
 1 2 3  


Added to Cart